Diatex
Site : http://www.diatex.fr
Diatex
56 Chemin des sources
69230 Saint genis Laval
Vous êtes ici : Diatex > Our divisions > Composite Division > Products > Vacuum moulding >> Bagging films

Our divisions

Bagging films

Bagging films are recommended for the moulding of elaborate forms. Advantages : good mechanical and chemical resistance, important elongation rate, non porous, cost effective. The most standard product for vacuum moulding is our polyamide bagging film PA205. Our new high performance bagging film PO180 with a 50 μ thickness helps to reduce wastes. You can also use our new eneration of high elasticity extruded advanced copolymer films. PO150XD2 or DIABAG have exceptional conformable characteristics, particularly when applied to awkward shapes with deep recesses or undercuts. It permits the moulding of complex forms, save time and wastes.

PA205 HF is a carved bagging film for the vacuum moulding of composite pieces. Its 3D structure provides a perfect vacuum drainage and so allows to take out the bleeder for compaction or vacuum moulding combinated to our MP Microporous peel ply. PA205 HF is a green bagging film, it enables use less peripheral device.

The new nylon bagging film Ref. PO180 limits waste. Used for vacuum moulding, 50µ of PO180 is equivalent to 75µ traditional film. It is available in lay-flat tubing and sheet.

PO180 is suitable with polyester and epoxy resins, its composition based on polyamide and polypropylene provides good mechanical and chemical properties.

ELASTIBAG is a very resistant film developed for debulding operations or for low temperature curing (below 80°C).

Associated with sealant tape LSM6000, it allows a large numbers of cycles because the sealant tape don’t dirty the film.

Its high deformability of 800% can match the most complex forms without the port.

Excel

Product Max Temp Thickness Width Length Auto-
release
Use with
resin*
Elastibag 80°C 550µ 1 to xm xm No E, PH, EL
PO120 120°C 75µ 2,4,6,8,10 m 75 m Yes E, P, VE, PH, EL
PO120 120°C 80µ 12/16m 53 m Yes E, P, VE, PH, EL
PO150 XD2 145°C 80µ 1.75/3.5 m 100 m Yes E, PH, EL
Diabag 80 135°C 80µ 1.7/3.4 m 50/100 m No E, PH, EL
Diabag 80 HT2 180°C 80µ 1.5/3 m 50/100 m No E, PH, EL
PO180  180°C 50 & 75µ 2/4/6/8/10/12m 60 to 400m Yes E,P,VE,EL
PO180T  180°C 50 & 75µ 0.31/0.60/0.80/1.2 m TUBE 100 to 200 m Yes E,P,VE,EL
PA205 205°C 50 & 75µ 0,80 to 4.57 m 250 m Yes E, P, VE, EL, TP
PA205 HF 205°C 75µ 1.60 m 125 m Yes E, P, VE, EL, TP
Silicone Bag 225°C 500µ 1.2 m 10 m Yes E, P, VE, PH, EL
PA232 232°C 50 & 75µ 0,80 to 4.57 m 50 & 75 m Yes E, P, VE, EL, TP
PTFE260 260°C 75µ 1.27 m 53 m Yes E, P, VE, PH, EL
Polyimide 400°C 25 / 50 / 75µ 1.57 m 57/76/116 m No E, TP
Polyimide HM 400°C 25 / 50µ 1,50m 100 m No E, TP

* resin code :
E = epoxy - P = polyester - VE = vinylester - PH = phenolic - EL = elastomer - TP = thermoplastic.
PO150 XD, Diabag 80 & Diabag HT2 maximum pressure capability : 4 bars/57 PSI.

Excel

Product Max Temp Thickness Width Length Auto-
release
Use with
resin*
Elastibag 176 F ,0217" 39 to x" xft No P, VE, E, PH, EL
PO120 248 F ,003" 79/157/236/314/394" 246 ft Yes E, P, VE, PH, EL
PO120 248 F ,0031" 472/630" 174 ft Yes E, P, VE, PH, EL
PO150 XD2 293 F ,0031" 69/138" 328 ft Yes E, PH, EL
Diabag 80 275 F ,0031" 67/134" 164/328 ft No E, PH, EL
Diabag 80 HT2 356 F ,0031" 59/118" 164/328 ft No E, PH, EL
PO180 356 F ,002&,003" 79/157/236/314/394/472" 197 to 1312 ft Yes E,P,VE,EL
PO180T 356 F ,002&,003" 12/24/31/47 328 to 656 ft Yes E,P,VE,EL
PA205 401 F ,002/,003" 31 to 180" 820 ft Yes E, P, VE, EL, TP
PA205 HF 401 F ,003" 63" 410 ft Yes E, P, VE, EL, TP
Silicon bag 437 F ,002/,003" 47" 32 ft Yes E, P, VE, PH, EL
PA232 449,6 F ,002/,003" 31 to 180" 164 & 246 ft Yes E, P, VE, EL, TP
PTFE260 500 F ,003" 50" 174 ft Yes E, P, VE, PH, EL
Polyimide 752 F ,001/,002,003" 62" 187/249/381 ft No E, TP
Polyimide HM 752 F ,001/,002" 59" 328 ft No E, TP
Retour haut de page